|
Inventory Updated: August 31, 2011 |
|
Inventory
|
|
Rod Breakdown Machines | Bullblocks | Deadblocks | Straighteners & Cutoffs | Nail Machines
Fence Machines | Mesh Machines | Chain Link Machines | Drawing Machinery, Intermediate
Descalers | Spike Machines | Thread Rollers | Spoolers | Misc.
|
Rod Breakdown Machines
|
7 Die Syncro; Non Ferrous, enter 3/8" cu/al, 250hp ac drive 3 speed gearbox, 36" spooler  1,2 |
| 6/7B Morgan; (6) 22" Blocks; 7 Die; 125 HP DC; 2250 Finish Speed; Start .217" L.C. 1,2,3 |
| 5/6HRM Vaughn; air and water cooled, enter .268" hc, 40/50/69hp ea block, 230/345v dc motors, 500-2500fpm, Burton (Mentor) Controls |
| 5HR Vaughn; 20/30 hp ea block, SCR Controls, down coilers, (1 Available) 1 |
| Vaughn 4/5 HRS Wire Drawing Line; 4 block - 5 die; 1st block double deck: 16"/20"; 20" intermediate blocks; 24" finish block; (4) 33 HP DC motors; wire dia. start: .216"-.205"; finish: .075" (1.9mm) approx.; air-water cooled blocks; Vaughn 24" x 40 HP DC drawing Deadblock; power turntable; single 6,000 lb. payoff - mechanical lift; no descaler 1,2,3,4,5,6 |
| Vaughn 4/5 HRS Wire Drawing Line; 3 block - 4 die; 1st block: 16"/20" x 40 HP DC motor; 20" x 33 HP intermediate; 24" x 33 HP DC finish; wire dia. start: .216"-.205" approx.; air & water cooled blocks; Vaughn 24" x 40 HP DC motor; drawing deadblock; powered turntable; Eiwa model EC-CD-8 Descaler: mechanical-brush-coat-heat; custom made dual 6,000 lb. cap; tower payoff, mechanical lift 1,2,3,4,5,6,7,8,9,10,11 |
| MacBee Mdl 24-BC-60; 3-block Wire Drawing Line; 24"x60 HP AC motors; 30" x 60HP AC drawing deadblock coiler; wire dia. start: .225"(5.8mm); wire dia finish: .130" (3.3mm); speed: 2000 FPM approx; Yaskawa varispeed AC controls 1,2,3,4,5 |
Eiwa Continuous Wire Drawing Line; 3 x 50HP blocks; 1 x 25HP Deadblock Coiler; max. rod inlet sizes approx: .350"-.312"(9.0-7.9mm); rod inlet: .216"-.250" (5.5-6.3mm); finish: .080"-.115" (2.0-2.9mm); 1st drawer: double deck-double die; block dia: 20"/25.98"; 50HP DC (37kW); blocks 2+3 same as block 1, only 1 die box; drawing deadblock coiler; 25HP DC x 26" block; electrical controls, mechanical descaler 1,2,3,4  |
Inline Wire Drawers
|
|
| 36" RMG Autodraw; 40hp, 150fpm, 5/8" cap. 1,2 |
Deadblocks
|
|
| 30" Ernst Koch Model KEWS IV-2 (700mm) Drawing Deadblock Coiler; 1 draft, 14-16%, max. inlet 5.3-7mm, .208"-.280", min. finish: .135" (3.4mm), high carbon, 2800 FPM (14M/sec), water cooled block, water cooled die, 100HP DC motor, 480V-3-60cycle, Mentor PLC electrical controls, turntable 1,2,3,4,5,6,7,8,9 |
| 26" Custom-made (Renco style) Drawing Deadblock; 40HP DC motor; 1750 RPM; Schultz relay controls 1,2,3 |
| 24" Morgan Drawing Deadblock; 75hp dc, 3.32:1 ratio, digital drive 1,2 |
| 24" Custom-made (Renco style) Drawing Deadblock; 40HP DC motor; 1750 RPM; Schultz relay controls 1,2,3 |
| 22" Renco Drawing; 75 hp DC SCR, 2000 fpm (2) |
| 22" Morgan; 50 hp, SCR controls, 3000 & 3600 fpm (2) |
| 22" Morgan DB-16 Drawing Deadblock Coiler; 22" dia. block x 8" face; max. start dia: .150" H.C., L.C., alloys; single draft; die mounted on flywheel;50/30 HP DC Motor: (1150/2300 RPM, 84/50 amps, 500V); ratio 5.61 to 1; max. speed: 3500 FPM approx.; max. die pull: 1200 lbs.; 4 belt drive pulley unit; manual lever raise/lower horn; no electrical controls 1,2,3,4,5,6 |
| 22" Macbee/Renco Style Drawing Deadblock Coiler; 22" block x 8" face; 50HP AC Induction Motor (875 RPM, 127/43 amps, 230/460 volts); max. start wire: .187" approx.; speed: 2100 FPM approx. (not to be exact); single belt drive - motor to flywheel shaft; manual lift low-raise horn; Allen Bradley SCR controls; constant torque AC drive 1,2,3,4 |
| 22" block Macbee/Whitacre style Drawing Deadblock Coiler; 22" block x 8" face; flywheel has multiple wheel guide sheeves; die holder; manual horn lift; 40HP AC Motor (amps 93.3 - 46.7, 1176 RPM, 230/460 volts); v-belt drive; finish wire dia: .125"-smaller 1,2,3,4 |
| 22" Macbee-Renco style Drawing Deadblock Coiler; 22" block x 8" face; flywheel has multiple wheel guides, sheeves, die holder; manual horn lift; air cooled block (blower fan); 40HP AC Motor, Baldor 3phase induction (amps 98/49, 1180 RPM, 230/460 volts); v-belt pulley; hand roll pointer (16 grooves); finish wire dia: .125"-smaller 1,2,3 |
| 16" Whitacre Drawing Deadblock Coiler; 16" air cooled block; wire dia. range: 1.2-3.1mm (.047-.125") approx; Baldor 20HP AC motor; 1700 RPM; 230/460V-60-3; Allen Bradley AC Electrical controls (new 2005) 1,2,3,4 |
| 16" Macbee Model 16DBLC-15A Drawing Deadblock; 16" block, 15HP DC motor, wire dia. coiling range: .047"-.125" (1.2-3.1mm), electric clutch braking system, dancer control unit 1,2,3,4,5,6 |
Straighteners & Cutoffs
|
|
| 10F Lewis; 3/8"-5/8" cap., 20' runout with flying shear 1,2,3,4,5,6,7 |
9C Lewis; stationary cut, 1/2" cap., 20' track, tooling  11,2 |
| 9F Lewis; 1/4" - 1/2" dia., 16' track with flying shear, 195 fpm 1,2,3,4,5,6,7,8,9,10 |
| Wafios R5; 6mm - 14mm capacity, 12m track, 90m/m 1,2,3,4 |
| 8F Lewis; Flying Shear; 5/32"-3/8" (.157" to .375") (4-9mm); .312" high carbon; speeds: 110 up to 195 FPM; 12' runout track; four-speed and two-speed; straightening arbors: 5 pairs of dies @ 3-5/8" centers; 3250 RPM; 4 straightening & 4 feed rolls; front feed housing: 2 sets of 2 feed rolls; cutoff: crank actuated traveling head with cam cutoff: 25 HP motor @ 1200 RPM 1,2,3,4 |
| 8F Lewis; 5/32"-3/8" cap., 12' runout with flying shear 1,2,3,4,5,6,7,8,9 |
| Shuster Model 2ABVF; wire dia range .157"-.375" (4 to 9mm); variable speed: 50 to 200 FPM; 21' runout track; electronic tripping mechanism cutoff; spinning arbor; stationary cutoff 1,2,3,4 |
| 4F Lewis; 4F x 20' straightener and cutoff 1/4" cap. 95-195fpm 1 |
| Lewis Model 2C4; wire dia. range: .093"-.250" (2.3-6.3mm); 16" runout track; 5HP; low-medium carbon wire; 5 die straightening arbor 1 |
| Lewis 2SV5-189-3; wire dia. range: .062" to .312"; 3' runout track; minimum cutoff: 1"; 65 to 250 FPM, variable speed; 160ppm up to 12"; dual center straightening arbor; 5 die; 15HP - 1800 RPM; height to center of wire: 47" 1,2,3,4,5,6,7,8,9 |
| Lewis 2CV4-434-3; wire dia. range: .062" to .250"; 3' runout track; minimum cutoff: 1"; variable speed range 65 to 200 FPM; 145ppm up to 12"; 7-1/2 HP Reeves drive; height to center of wire: 45" 1,2,3,4,5,6 |
| Lewis 1SHV-HS; wire dia. .062" to .135" (1.5mm to 3.5mm); 4' runout track; minimum cutoff 2"; variable speed drive; 25-250 FPM; additional catalog details upon request. (2 available) 1,2,3,4,5,6 1,2,3,4,5 |
| Lewis 1SHV; wire dia. .031" to .135" (.79 to 3.5mm); 4' runout track; minimum cutoff 2"; variable speed drive; 250-400 FPM; additional catalog details upon request. (3 available) 1,2,3,4,5 1,2,3,4,5 1,2,3,4,5 |
| Lewis 1C; .020"- 1/8" cap. x 4' track, (20 Available) 1,2 |
Mesh Machines
|
|
| Schlatter Model MG201; semi-automatic; cross + longitudinal wires pre-cut; line + cross wire min.-max. 5.0 to 12.0mm (.196"-.472"); min. + max. welding width: 48" to 126" (4' - 10'5"); max. cross wire length: 130" (10'8"); mesh length: min-max: 80"-480" (6'6" - 40'); no. of welding positions: 64 - fixed every 2"; turning & stacking: mesh robot; advance system: roller advance LVR and mesh pullout MVL; transformer capacity: 16 @ 100 KVA; supply voltage: 380V - 50/60 cycle; control software: Sestep 530; weld control: Schlatter, type MP6 x 1321 1,2,3,4,5 |
| EVG G 45/102 Wire Mesh Welder; working range: number of line wires (equipped for) 15, line wire diameter 3.0 – 8.0 mm, cross wire diameter 3.0 – 8.5 mm, cross wire spacing, steplessly adjustable from 50 – 400 mm, line wire spacing 100,150,200,300 mm, max. distance between outer line wires 2600 mm, max. width of wire mesh 2750 mm |
| EVG Model GZN/75 Wire Mesh Welder; max. welding width 75"; max. working width 80"; line + cross wire dia: .040-.135" (1.0-3.4mm); line wire spacing 1"-8" in steps of 1"; cross wire spacing 1/2" to 6" in steps of 1/2" + 1"; max. number of line wires 76; line consists of: payoff tower, cross wire payoff, (2) 7-roll pull stations, digital counter, tension stand, EVG cross wire feeder, line wire straightener, hydraulic trim-shear, 5-head pneumatic crimping unit, EVG roll take-up, electrical controls 1,2,3,4,5,6,7,8,9,10,11,12,13,14,15 |
| 8' mesh welded mesh line; 3 - 6.6mm wire dia., 3" x 3" min. spacings, App. 80 spm, Line and cross wires from wire carriers, Shear and roll take up, Can be inspected under power 1 |
Chain Link Fence Machines
|
|
| 12' Bergandi Chain Link Machine; New 2011 1,2,3,4,5,6,7,8 |
| Wafios VDF-80 Chain Link Fence Machine; 4000mm width; 1.5 to 3.8mm (.060"-.149"); 1830 sq ft hour @ 2" mesh @ 5 to 6' wide; chain link mesh sizes min.-max: 3/8" to 3-1/8"; roll take-up (5 Available) 1,2,3,4,5 |
Fourslides
|
|
| Baird Model No. 324 Fourslide; Capacity: 3/16" Diameter Wire, 1-1/8" Width Strip Metal, 24" Std. Feed Length and 26-1/2" Feed Length without Stops. Includes: "H" Block Form Bracket, Stripper Arm w/ Cam, Form Lifter Arm w/ Cam, Stock Check, Cutoff Unit, Removable Cams on, Carriers, 2-Plane Wire Straightener, Auto Lubrication System, 3 HP Reeves Variable Speed Drive Motor and Control 1,2
|
Turksheads
|
|
| Karl Fuhr Type F, Model 5-F Indenting-Rolling Unit; max. wire: 16mm; dia. rolls: 8" x 1-1/4" thick; 3-roll unit; manual adjustment; mounted on steel frame base; 3 roll guide unit 1,2,3,4
|
Slitting Lines
|
|
| 48" X 6" X 20,000 LB Dahlstrom Pull Thru Slitting Line; Hand Of Line: Right to Left, Capacity: 26 Cuts @ .015", 3 Cuts @ .188", Weight Capacity: 20,000 LBS, Uncoiler Model 2SCR2, Range I.d. 19" - 25", Traversing Base 8", Slitter Capacity 11 GAUGE X 48" W, Thread Speed 75 FPM, Feed Up Drive 15 HP, Arbor Diameter 6", Entry Edge Guides, Entry Pass Line Rolls, Recoiler, Mandrel 58", Drum Diameter 20", Manual Clamp, Manual Expansion, Bottom Hydraulic Pushoff, Duty Master Motor 50 HP / 220/440 / 60 / 3 / 1675, Overarm Separator Capacity 48", Coil I.d. 60" 1,2,3,4,5
|
Spoolers
|
|
| 30" Heavy-duty Traversing Base Spoolers; 30" x 14" traverse; 4280 FPM approx.; Dynamatic AC 5HP Eddy Current motor with electric clutch brake; Boston torque 1/2HP (Baldor) motor for traverse; Pulley belt drive; manual lever spooler secure-release; electrical control; spooler constructed of heavy steel welded frame and base (2 available)1,2,3,4,5,6,7,8,9,10,11 1,2,3,4,5,6,7,8,9,10
|
Thread Rollers
|
|
Ruja Tool Planetary Thread Roller with automatic painting unit  1 1,2,3,4,5 |
Nail Machines
|
|
| Wafios N3; wire dia. range: 1.0-2.2mm (.039"-.086"); nail length: 10-500mm (.393"-1.9"); 700 NPM (approx); 3 HP; Bijur lube unit; 2 plane wire straightener 1,2,3,4 |
| Tanisaka Model MTG-B; wire dia. .065" to .095"; nail length: 1" to 2"; NPM: 400 approx.; mfg. 1975 1 |
| Tanisaka Model MTG-C; wire dia. .095" to .134"; nail length: 1-3/4" to 3"; NPM: 350 approx.; mfg. age 1975; (2 available) 1,2 |
| Tanisaka Model MTG-D; wire dia. .134" to .165"; nail length: 2-1/2" to 4-1/4"; NPM: 280 approx.; (2 available - 1974 & 1975) 1,2 |
Misc.
|
|
| RENCO Double Head Skin Pass; 25 hp ea. block was drafting 8%, Sabina Drives (2) 1,2,3 |
| Pointers - Welders - Spoolers - Wet Wire Drawers and more... |
|
